VidPro J150 User Manual download pdf

J150 COMPRESSORJ150 COMPRESSOR

J150 COMPRESSOR

Installation and OperationInstallation and Operation

Installation and Operation

ManualManual

Manual

Installation Check ListInstallation Check List

Installation Check List

Mount the compressor as shown, with both feet

either underneath or on the side. The mounting plate

should be flat and strong enough to support 120 lbs.

For air circulation, there must be an 8" x 8” hole in

the center of the mounting plate or 1” spacer blocks

under the mounting feet.

The long capscrews (35mm) should be used on the

feet. Tighten to 26 ft. lbs.

Rotation of the machineRotation of the machine

Rotation of the machine

is shown by the arrow on

the body between the suction and delivery port.

- Arrow points to suction port. -

Mount the machine so that the rotation matches the

PTO rotation. To change rotation, remove cowls,

switch drive flange/yoke to other end of compressor,

and replace the cowls.

Do not force end yokes or drive flange onto the

compressor or PTO shaft.

Use a tube type balanced PTO drive shaft, parallel

with the PTO output shaft axis within 2° to ensure

vibration-free running. The maximum driveline angle

is 10°.

A 30 or 36psi relief valve should be mounted 12”-24”

from the compressor discharge with valve outlet

away from machine and filter inlet.

The air filter should be mounted in an

uprightupright

upright

position at least 12” from compressor inlet, with free

access to element and away from exhaust fumes

and road spray. For tractor mount, we recommend

above frame rails behind the cab.

Suction (1½” I.D.) and delivery pipework (1½” I.D.,

1” I.D. minimum) should be free of weld beads or

foreign material and supported by brackets. Do not

contaminate the inside of the piping with Teflon tape

or pipe dope thread sealer.

If pipework runs to the opposite frame rail, it must

have a flexible section to prevent distortion of the

compressor.

Install discharge filter (p/n 713031200, M202 or

equivalent) with minimal restriction, to prevent

compressor overheating.

A 3-way ball valve (1”) should be installed into

delivery pipework to bleed air and control system

pressure. The ball valve should be installed prior to

Chicago fitting to manually isolate the compressor

from the trailer.

A liquid-filled pressure gauge is recommended in the

delivery pipework for ease of operation and system

troubleshooting.

The operating speeds are:

• 1000 -1800rpm for J150

• For optimum performance 1200-1400rpm is

recommended.

Calculate engine speed using the PTO ratio.

A constant speed governor or throttle control system

is recommended.

Check compressor speed with tachometer to ensure

proper operation.

Post engine speed in cab on label provided.

ypical Inlet Pipe Wypical Inlet Pipe W

ypical Inlet Pipe W

orkork

ork

Arrangement - Side Mount PArrangement - Side Mount P

Arrangement - Side Mount P

ortsorts

orts

Chicago Fitt

# 531296200

3-Way Ball Valve

# 705011205

Check Valve

# 705012205

12” Min

Relief Valve

# 705011205 - 30 psi

Option - 36 psi

# 705000216

Mtg Brkt (optional )

(2) pc # 712000202

Inlet Air Filter

# 713000205

12” Min or as

req to clear

1-1/2”

Pipe Typ

Truck frame

rail

ypical Outlet Pipe Wypical Outlet Pipe W

ypical Outlet Pipe W

orkork

ork

Arrangement - Side Mount PArrangement - Side Mount P

Arrangement - Side Mount P

ortsorts

orts

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Installation Check List

J150 COMPRESSORJ150 COMPRESSORJ150 COMPRESSORJ150 COMPRESSORJ150 COMPRESSORInstallation and OperationInstallation and OperationInstallation

Page 2 - Installation - Notes

Port FlangesPort FlangesPort FlangesPort FlangesPort FlangesDescriptionDescriptionDescriptionDescriptionDescriptionpart numberpart numberpart numberpa

Page 3 - Operation

Important NotesImportant NotesImportant NotesImportant NotesImportant Notes• These instructions are not intended to modify or circumventany company p

Page 4

Page 5 - Bill of Material

Bill of MaterialBill of MaterialBill of MaterialBill of MaterialBill of MaterialDetailDetailDetailDetailDetailQtyQtyQtyQtyQtyPPPPPart No.art No.art No

Page 6

SAFETYSAFETYSAFETYSAFETYSAFETYPRECAPRECAPRECAPRECAPRECAUTIONSUTIONSUTIONSUTIONSUTIONS•••••Rotating shafts can be dangerous. YRotating shafts can be d

Page 7 - Louisville, KY 40299

WWWWWARRANTYARRANTYARRANTYARRANTYARRANTYWARRANTY: The Seller warrants the goods sold hereunder against defects in workmanship or materials under norm

Comments to this Manuals

No comments

VidPro J150 User Manual

Browse online or download User Manual for Air compressors VidPro J150. VidPro J150 User's Manual

Summary of Contents

Comments to this Manuals